|
Written by Aaron Selway
|
|
Friday, 05 June 2009 |
Savvy Offroad's New Skid for TJ’s 
JeepsUnlimited’s own mrblaine has formed a new company with partner Gerald Lee (provelogear) to bring new lightweight products to the off-road world.
|
|
Last Updated ( Friday, 05 June 2009 )
|
|
Read more...
|
|
|
Written by Aaron Selway
|
|
Friday, 22 May 2009 |
ROKMEN HopLite™ Aluminum Armor 
Introducing the new ROKMEN line of HopLite™ Aluminum Armor for the 97-06’ Jeep
TJ and LJ Wranglers. Hoplite™ full coverage corners and Hoplon™ tub rails add both
style and protection to your Jeeps backside. Both items are constructed from 6061 T6
Aluminum for an incredible strength to weight ratio, while keeping added weight above
the vehicles center of gravity to a minimum.
Hoplite - Heavily armored infantry soldiers of the ancient Greek era.
Hoplon - The principle shield of the Hoplite heavy infantry warrior.
|
|
Last Updated ( Wednesday, 05 August 2009 )
|
|
Read more...
|
|
|
Written by Aaron Selway
|
|
Monday, 11 May 2009 |
Cervini's Hoods for the Jeep TJ
 97-06 Jeep Wrangler 3" Cowl Hood
Cervini's Auto Designs 97-06 Jeep 3" cowl hood provides plenty of clearance for engine upgrades and cools under hood temps. The Cervini Jeep Wrangler 3” Cowl Hood is constructed with a finished underside liner that adds extra strength and can be painted for a show quality appearance. (Part# 1190 $539.00)
Available for 97-06 Jeeps this hood is a direct bolt-on, made of hand laid premium fiberglass (which will not rust), and features screened rear air vents. The hood is guaranteed to fit perfectly and utilizes your OEM hinges and latch. Cervini's Auto Designs Jeep Cowl hood also includes all hardware necessary for installation. 97-06 Jeep Wrangler Ram Air Hood
 Cervini's Auto Designs 97-06 Jeep ram air hood features a pre-cut single scoop design that includes a brushed aluminum billet grill and cools under hood temps. The Cervini Jeep Wrangler Ram Air Hood is constructed with a finished underside liner that adds extra strength and can be painted for a show quality appearance. (Part# 1191 $579.00)
Available for 97-06 Jeeps this hood is a direct bolt-on, made of hand laid premium fiberglass (which will not rust), and features screened rear air vents. The hood is guaranteed to fit perfectly and utilizes your OEM hinges and latch. Cervini's Auto Designs Jeep Ram Air hood also includes all hardware necessary for installation.
Contact: Cervini’s Auto Designs, 3656 N. Mill Rd, Vineland, NJ 08360 800-488-6057 www.cervinis.com |
|
Last Updated ( Friday, 22 May 2009 )
|
|
|
Written by Administrator
|
|
Friday, 17 November 2006 |
In May of this year I attended the annual JeepsUnlimited event Moab, Utah where a potluck dinner was held mid-week and door prizes were given out from a wide variety of vendors. I was fortunate to receive an aluminum fuel tank skid plate that was provided by Toys By Troy out of Phoenix. This Company manufactures impressive products for Jeeps, and I am impressed with this skid. It is very light, yet quite strong with a double layer of aluminum plate on the bottom where strength is needed most. Check them out at http://www.toysbytroy.com/ |
|
Last Updated ( Wednesday, 13 December 2006 )
|
|
Read more...
|
|
|
Written by Administrator
|
|
Thursday, 02 November 2006 |
One of the first modifications every Jeeper completes is to swap the stock bumpers for something that handles more abuse and adds a bit of style to their Wrangler. Nothing changes the attitude of your Wrangler more than replacing the thin sheet metal Daimler-Chrysler gives you from the factory. When I wanted to upgrade the front bumper on my 2004 Wrangler Unlimited, I had a few requirements. First, it must have an integrated winch mount. In an effort to keep my vehicle as slim as possible, a bumper with a separate winch mount adds weight that I did not need to carry around all the time. Second, it must have a winch guard. I wanted one for the extra protection but also for the appearance. A winch is an expensive piece of equipment and providing it with a little bit of protection is a good thing. Third, shackle mounts that are not welded to the face of the bumper. Something welded on the front and back helps spread out the load. Lastly, it must provide better clearance. Clearance is the key to our hobby. Anytime you can gain clearance, you're improving the off road ability of your vehicle. |
|
Last Updated ( Wednesday, 03 January 2007 )
|
|
Read more...
|
|
|
|
<< Start < Previous 1 2 Next > End >>
|
| Results 1 - 9 of 12 |
TJ Wrangler
