Backspacing with 35x15x15

XJONBOGGERS · 11-10-2006, 02:00 PM

I am lifting my xj with a 6.5inch Rough Country lift that says it will clear
35x12.50 but I am looking to run a 35x15x15 TSL BOGGER do you think that a 3 inch backspacing will be good or should I go 2.5" I will trim a little but don't want to trim too much I am also thinking about using a 2 inch spring spacer with the kit for the little extra I wil need

XJONBOGGERS · 11-10-2006, 02:08 PM

I also would like to add that I live in florida and will not be rock climbing because we don't have rocks like that we only have mudd and sugar sand

jpnjim · 11-10-2006, 10:10 PM

Are you using the stock ft axle?

35x14.5" Boggers are alot of tire for a stock 30.

If your using a different ft axle, backspacing will depend on what the new axle width is.

Are you gonna run them on the recomended 15x10's, or try to squeeze them onto 15x8's?

BTW, even with 6.5", you're gonna have to more than a 'little' trimming to fit these Boggers, even if you limit uptravel.

Adding a 2" spacer to the 6.5", instead of trimming = a ton of lift for 35's.

stam89xj · 11-11-2006, 02:37 AM

what gear(r&p) ratio do you plan on running?

XJONBOGGERS · 11-14-2006, 08:44 PM

I plan on running alot of gear and eventually switching to the full width dana44 and ford 9 inch i have but i don't want to swap them right now.
I planned on like 5.13 gears or something around there and either a 15x10 or a 15x12 with like a 3 inch backspacing it will not be driven on the street it is only going to be a mudd truck

11-10-2006, 02:00 PM	#1
XJONBOGGERS Registered Join Date: Nov 2006 Posts: 13 Thanks: 0 Thanked 0 Times in 0 Posts	Backspacing with 35x15x15 I am lifting my xj with a 6.5inch Rough Country lift that says it will clear 35x12.50 but I am looking to run a 35x15x15 TSL BOGGER do you think that a 3 inch backspacing will be good or should I go 2.5" I will trim a little but don't want to trim too much I am also thinking about using a 2 inch spring spacer with the kit for the little extra I wil need

11-10-2006, 10:10 PM	#3
jpnjim Join Date: Jun 2001 Location: Ma... Posts: 7,241 Thanks: 19 Thanked 2 Times in 2 Posts	Are you using the stock ft axle? 35x14.5" Boggers are alot of tire for a stock 30. If your using a different ft axle, backspacing will depend on what the new axle width is. Are you gonna run them on the recomended 15x10's, or try to squeeze them onto 15x8's? BTW, even with 6.5", you're gonna have to more than a 'little' trimming to fit these Boggers, even if you limit uptravel. Adding a 2" spacer to the 6.5", instead of trimming = a ton of lift for 35's. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-10-2006, 02:08 PM	#2
XJONBOGGERS Registered Join Date: Nov 2006 Posts: 13 Thanks: 0 Thanked 0 Times in 0 Posts	I also would like to add that I live in florida and will not be rock climbing because we don't have rocks like that we only have mudd and sugar sand

11-11-2006, 02:37 AM	#4
stam89xj Registered Join Date: Dec 2002 Location: aston,pa Posts: 4,972 Thanks: 0 Thanked 2 Times in 2 Posts	what gear(r&p) ratio do you plan on running?

11-14-2006, 08:44 PM	#5
XJONBOGGERS Registered Join Date: Nov 2006 Posts: 13 Thanks: 0 Thanked 0 Times in 0 Posts	I plan on running alot of gear and eventually switching to the full width dana44 and ford 9 inch i have but i don't want to swap them right now. I planned on like 5.13 gears or something around there and either a 15x10 or a 15x12 with like a 3 inch backspacing it will not be driven on the street it is only going to be a mudd truck